Showing results: 421 - 435 of 876 items found.
-
Model 4912 / 4912PR -
Aplab Limited
- Microprocessor based Fully Automatic L, C, R, Q and D measurement- Autoranging with Direct Digital Readout- 4 Terminal Measurement Technique- No Tuning or Balancing- Series or Parallel Equivalent Measurement- Absolute Value and Nominal Value with Percentage Tolerance- Single / Multiple Parameters Check During Component Sorting- Feather Touch Keys with Audio Feedback- Thermal Shut Down for Overheat Protection- Special Mechanism for Fast and Easy Insertion and Removal of Test Component- Low Cost and Portable- Component Sorting on Absolute or Nominal Value Basis with a Percentage Tolerance- Aplab Model 4912PR is Remote Programmable Auto Compute LCR-Q Meter Sorter, Which can be Programmed through GPIB, RS232 or SPIB Interface
-
Aero Nav Laboratories, Inc.
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
Global Testing Services Inc.
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
P.H.D. Family -
Ultra-X INC.
Performs component level motherboard testing utilizing direct hardware-to-hardware communication and displays simple PASS or FAIL results on the system monitor. This mode is used to run tests on a system that successfully completes POST (i.e. the system is capable of displaying a screen when power is on).
-
UC8310 -
UC Instruments, Corp.
The UC8310 Desktop Variable Optical Attenuator offer superior performance for channel balance, power equalization, gain tilt and power adjust of DWDM system, EDFA, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications.
-
Keysight Technologies
Test & measurement capabilities for analyzing polarization properties of optical signals are indispensable in todays optical R&D-labs and manufacturing floors. The Keysight N778x Polarization Analysis and Control series offers high speed instruments for high performance characterization and verification of optical components and sub-systems.
-
Amida Technology, Inc.
The AMIDA-3KS test system provides a lower cost, cost-optimized test solution for all consumer power management ICs and portable product components. The AMIDA-3KS tester provides 6 board slots in the test head for the required number of analog board channels, thus reducing the overall system procurement cost, making the cost-effectiveness of each board channel 2 times higher and more flexible. The customer's product testing time is greatly shortened.
-
Dongguan Kejian Instrument Co., Ltd.
Test method uses clean ball placed within the material applications, steel ball itself of the impedance and total weight, must be in conformity with the provisions, on this condition detection material zigzag waterproof penetration index, using the latest inductive components and special design, test as long as materials applications in water infiltration immediately automatic stop counting or in setting time (test times) arrived, namely automatic stop and display the time or times.
-
LXinstruments GmbH
With cars it is easy: Change of oil, check of breaks and V-belt .. etc. - that is normal. But your test system does not need all these things. However it makes sense to look after your test system occasionally and check or change special idems. If you take the time and plan a preventive maintenance your test system will have less unplanned failure times. Less dust means less heat and slower ageing of electronic components.
-
MST-8101/8103 -
Matrix Technology Inc.
Multi-channel output is an internal high-voltage switching module attached at the bottom of the instrument. Through multi-channel output module, multiple test points of the components can be connected with multiple channels at a time. During testing, the instrument can be set to control the channel switch. Controllable testing can be achieved by connecting the corresponding port to withstand voltage test terminal. With this multi-channel module, rapid connection can be achieved through test fixture without changing ports during the testing process.
-
TOPTEST GmbH
You are looking for a LabVIEW-solution for a test problem? LabVIEW is an excellent development environment for all areas of metrology. Here we have extensive experience and can help in your test problems. In the LabVIEW programming language, we develop VIs (Virtual Instruments) that can be integrated easily in TestStand. Using hardware-oriented programming languages such as C# and LabVIEW, we develop integrations of control and measurement components.
-
OptiConcepts
OptiConcepts FiberWarrior Pro™ Insertion Loss Test Set is used for the following functions: continuity check, fiber loss, return loss, and connector loss for OEM, lab, and production use as well as transport, metro, access, and FTTx/PON networks. The FiberWarrior Insertion Loss Test Set performs single-mode and multimode loss measurement functions, including single component and multi-fiber testing.
-
Telerik A.D.
Test Studio Dev Edition is a Visual Studio extension allowing software engineers to create functional automated UI tests in Visual Studio using C# or VB.NET. It is designed to provide ready-to-use Visual Studio automated testing functionality across web and desktop. Applications that are built with the Telerik and Kendo UI controls can be automated in a snap, by way of built-in native component translators.
-
NX Pro+ -
Dynalab Test Systems, Inc.
The Dynalab NX Pro+ Wire HarnessTester is modular and is designed for applications requiring up to 32,768 test points. It has the same front end as the NX Pro Tester, but employs a series of Expansion Units to accommodate the test point cards. Testing for continuity, shorts, and a variety of components. Highly flexible and adaptable product line that meets the changing needs of wire harness manufacturers.
-
MM14 -
D.Marchiori s.r.l.
The MM14 is a digital technology pressure standard calibrator. It consists of a variety of components combined to allow ease of operation for the verification of pressure based UUTs (unit under test) such as Air Data Test Sets.The MM14 utilises a very accurate dual pressure transfer standard generator, a reference Primary Standard dead-weight and PC based operating system for automatic verification of the U.U.T.
